WarmGlass.com

much thanks for the quick reply...........yes you answered my question...now back to work..........thanks

want to put in a pot melt his am....ready to go but I see i dont have enough height (pot from shelf) my kiln is not deep. can i put shelf on floor of kiln?

dont have them to refer to but.......curious how the patterns were acheived.no one in particular..........s.andblasted?

Cut and fused various zoo animals (gift for expecting daught-in-law).......How can I slump them so that they will stand ........like Newy Fagen's horses?

Just made a one layer plus design plate and got a bubble in the middle...it did burst... Can I refuse it ? Will it flatten if I put a small frit on the outside os the rim allowing air to escape?

Has anyone tried to make a hole in a glass block used for building? Is it temered glass? What is the best way to try this?

beautiful site brock but it doesnt explain how it is done.

Where is a good source for copper and gold leaf?

Want to sandblast and need advice. I bought the cabinet from HF...comes with the siphon gun.....Is this system okay for satin finishes and also some deeper more detailed work (dont want to outgrow this quickly and make the same mistake I made with other tools I purchased)....What is better......pres...

so that means that anyone who does pattern bars is copying Lisa? or raking is copying Patty..........how absurd!

THE HORSE IS DEAD...........GET OFF IT.

I have a fused piece that I want to slump into a large square mold. The piece has pattern bars on the sides which spread at a bit in the fuse and now extends over the side os the mold by 1/8 of an inch. Should I cut this down, fire polish then slump? Will this 1/8 make a difference?

I really could not help you as you have more experience than I do...just to add I have a Jen_Ken 24 and I get full fuse at 1420 with 15 min soak..still anneal BE at 960.....go figure.............

on my way out to portland for glass shopping....my first time there. Any suggestions as far as purchasing...best buys, places to go etc....

I have been fusing and slumping sinks for quite awhile now. There are numberous answers to your question but I need the following info in order to help you out..... Your exact fusing schedule ............and your exact slumping schedule that you have used for 3/4" float. I can then relate that ...

I have repeatedly tried working with copper and have had no luck keeping the copper to maintain it's color. It consistently turns a dark purple!!! I have read and abided by the o2 theory, tried different firing methods all w/out success!!! Hard to believe that some of the beautiful copper work i hav...

Just made my first mold -raku clay....After a week it is 'leatherhard'...Now what do I do. I need a schedule for firing it o bisque then what schwdule do I use for slumping into it? Would it be different than BE molds?

I called Marty at CDV (even though I bought the kiln from Mike) and he was very kind to help me. The problem was with the saftey switch...The lid wasnt sitting on it properly; therefore the kiln was not heating up properly. Thanks for all of your help as well.................Luckily a minor problem....

Interesting reading everyone's comments. Now would love to see the work ...How do I find it?

I have had my Jen for 8 months 24"....When I first got i, it was firing on the hot side so 1420 was always a full fuse for me. This past week it is doing strange things and I hope someone can help....Using same schedule and glasss as always but now at 1420 I get barely a tack fuse and none of t...

Ron advice pls.....Just make my own molds with raku (you inspired me) they have been sitting lightly covered with plastic but dont seem to be drying out? How long should this take. It is cold in my garage....Ill have real mold soon......green :lol: Then when I do fire...can u give me a firing schedu...