Search found 97 matches
- Thu Feb 26, 2004 7:04 pm
- Forum: Techniques and Tools
- Topic: Sanblasting with Photo's
- Replies: 4
- Views: 4933
Do you know about half-tones, line counts, positive and negative films? Do you know any darkroom terminology and procedures? You need to render your image as a film if you want to use the photosensitive films used in producing photographic images by sandblasting (or screen printing and other graphic...
- Thu Feb 26, 2004 10:08 am
- Forum: Techniques and Tools
- Topic: sandblasting
- Replies: 25
- Views: 28374
Try this to see my sample of 3/4 inch glass cut through with high pressure sandblasting
http://photos.yahoo.com/eugenelohman
or:
http://f1.pgphotos.yahoo.com/ph/eugenelohman/my_photos
http://photos.yahoo.com/eugenelohman
or:
http://f1.pgphotos.yahoo.com/ph/eugenelohman/my_photos
- Thu Feb 26, 2004 9:21 am
- Forum: Techniques and Tools
- Topic: Sanblasting with Photo's
- Replies: 4
- Views: 4933
- Thu Feb 26, 2004 8:28 am
- Forum: Techniques and Tools
- Topic: sandblasting
- Replies: 25
- Views: 28374
- Thu Feb 26, 2004 8:11 am
- Forum: Techniques and Tools
- Topic: sandblasting
- Replies: 25
- Views: 28374
You guys are right. It takes a MONSTER to do the cutting I want to do. There has to be a compressor out there that is scaled to the needs of someone who isn't necessarily going to sandblast bridges and ships and who only wants to cut AWAY some glass. I had a shop test-cut a piece of 3/4 inch glass a...
- Wed Feb 25, 2004 9:08 pm
- Forum: Techniques and Tools
- Topic: sandblasting
- Replies: 25
- Views: 28374
Hey all, I just talked to a man with 50 years experience sandblasting monuments. He says the small 15 lb pressure pots are good and you can do a lot of work with them but the critical factor is having a compressor that delivers a minimum 35 cfm continuously. So it's the volume of air that is importa...
- Wed Feb 25, 2004 8:58 pm
- Forum: Techniques and Tools
- Topic: Ceramic glazes fired on glass
- Replies: 1
- Views: 3133
Sandi, I have fired cone 06 ceramic glazes on glass with results I was pleased with. Of course, they are decorative only and not food safe. I haven't fired the copper you asked about and all my examples had the glaze on the surface. It is possible to cap the glaze with another sheet of glass to make...
- Tue Feb 24, 2004 10:25 pm
- Forum: Techniques and Tools
- Topic: Kiln Purchase
- Replies: 9
- Views: 8899
No problem. Usually, the size of shelf is determined by the size of kiln. A given shelf works for any size project as long as it fits on the shelf and the shelf fits in the kiln. You can order kiln furniture to fit the kiln you buy. As far as I know no math is required other than will the kiln shelf...
- Tue Feb 24, 2004 9:51 pm
- Forum: Techniques and Tools
- Topic: Kiln Purchase
- Replies: 9
- Views: 8899
There are kiln manufacturers who sponsor this website. Take a look at the kilns at the top of your screen. There are both front and top loaders. I've only had experience with two kilns: the small 16 inch diameter ceramic kiln I used to make pottery and the Denver kiln I have now. A national radio ho...
- Tue Feb 24, 2004 9:23 pm
- Forum: Techniques and Tools
- Topic: Kiln Purchase
- Replies: 9
- Views: 8899
You're going to get lots of advice. Everyone has their favorite kiln for many reasons. My advice is get the largest kiln you can afford and make sure it has a digital controller and vent to out doors. Do you plan on making some or all of your income with your kiln or will it be a hobby? I don't inte...
- Tue Feb 24, 2004 7:25 pm
- Forum: Techniques and Tools
- Topic: sandblasting
- Replies: 25
- Views: 28374
Mark Hughes: I just surfed over to Harbor Freight and those smaller pressure pots are very interesting. Do you have personal experience? I want to be able to do both light etching, deep carving and all the way to cutting through 3/4 inch glass. I had a local shop do a test cut for me and it worked s...
- Tue Feb 24, 2004 6:50 pm
- Forum: Techniques and Tools
- Topic: sandblasting
- Replies: 25
- Views: 28374
- Sat Feb 21, 2004 8:09 am
- Forum: Techniques and Tools
- Topic: sandblasting
- Replies: 25
- Views: 28374
sandblasting
I'm looking for an alternative blasting medium to the silicon carbide I usually use. I'll be renting a pressure pot and compresser. The guy at the rental says I can't recycle the medium because it might damage the pressure pump. I told him I was going to do the work in a clean enviornment (you know,...
- Wed Jan 28, 2004 3:05 am
- Forum: Business Topics
- Topic: Pricing a glass staircase
- Replies: 0
- Views: 6956
Pricing a glass staircase
The stringers are already built and are engineered for glass treads and landings. I'm trying to estimate pricing and have some preliminary figures. It makes me wonder: What are you guys getting for a project like this "out there"? I was planning on stack fusing the treads and laminating th...
- Mon Jan 12, 2004 1:53 pm
- Forum: Techniques and Tools
- Topic: Tauras ring saw
- Replies: 41
- Views: 35260
- Wed Nov 19, 2003 3:45 pm
- Forum: Techniques and Tools
- Topic: looming deadline: how fast can I fire
- Replies: 9
- Views: 8650
Thanks everyone for the feedback. I'll test-fire a sacrificial sheet. I have a kiln with elements in the lid and can ramp up very quickly. Probably straight up to 1270 then OFF, no hold or soak. I'll flash-vent to 1000 F and then let the kiln cool naturally. I'll crack the lid a bit at 350. I'll be ...
- Wed Nov 19, 2003 10:26 am
- Forum: Techniques and Tools
- Topic: looming deadline: how fast can I fire
- Replies: 9
- Views: 8650
- Wed Nov 19, 2003 9:21 am
- Forum: Techniques and Tools
- Topic: looming deadline: how fast can I fire
- Replies: 9
- Views: 8650
- Wed Nov 19, 2003 3:59 am
- Forum: Techniques and Tools
- Topic: looming deadline: how fast can I fire
- Replies: 9
- Views: 8650
looming deadline: how fast can I fire
I'm firing a ceramic lustre on double strength float. Pieces range from 14" x 39" to 13" x 28". I typically fire at 10 degrees F per minute up to 1100 F and then 20 degrees per minute to my target which of course varies. How fast can I go to 1270 degrees F and do I have to follow...
- Sat Oct 25, 2003 10:34 pm
- Forum: Techniques and Tools
- Topic: De-stressing tempered glass.
- Replies: 13
- Views: 12973