WarmGlass.com

Hi All!

I'm a newcomer. LOVE this site! Please tell me the brand of the best stripcutter and where I can find it. Thanks so much.

Nadine

Nadine- check the archives, this is a subject dear to our hearts and it comes up repeatedly. Marty

Nadine, I got a large custom made Scoreboard from the folks that make them and it is great. It accomodates a whole sheet of BE which can be stripped in about 10 minutes using your own cutter. It is just a base board with a set bar at the bottom and a raised perpendicular bar that the glass slides under. Make a mark on the bottom bar and start sliding and scoring, using the perpendicular bar as a guide for your cutter.

Lisa

Lisa sounds good but who makes them?

I have two new high-teck strip cutters for sale at $400 plus shipping.
They were made for prototypes and are similar to those selling for over $700.
Call John at Water Jet Design 503-615-0144.

Thanks Marty and Lisa!! I'll check into the avenues suggested by both of you. It is really nice to have this website so that this wonderful help is available.
Nadine

doctac wrote:Lisa sounds good but who makes them?

Here is the addess for the folks who make them. THey come in a standard size that is fairly small for my purposes, but were happy to make one to my specs. Talk to Mark and tell him Lisa Allen in Memphis referred you.

http://www.emeraldrainbow-wedgies.com/scoreboard.htm

Lisa

much thanks lisa and your work is F A N T A S T I C!!!!! (Its okay to yell that out

I had someone to make one like Marty uses that I think Vitrum is selling. Works great and I think it is the best think if you have a fixed place to put it. Thanks Marty for the idea.
John

Check out this thread:

http://www.warmglass.com/phpBB/viewtopic.php?t=2869

- Paul

Nadine Green wrote:Hi All!

I'm a newcomer. LOVE this site! Please tell me the brand of the best stripcutter and where I can find it. Thanks so much.

Nadine

Lisa Allen wrote:Nadine, I got a large custom made Scoreboard from the folks that make them and it is great. It accomodates a whole sheet of BE which can be stripped in about 10 minutes using your own cutter. It is just a base board with a set bar at the bottom and a raised perpendicular bar that the glass slides under. Make a mark on the bottom bar and start sliding and scoring, using the perpendicular bar as a guide for your cutter.

Lisa

The instructions on the Scoreboard look backwards to me. If I'm right handed , I would have the cutter in my right hand and would want to cut on the right side of the vertical bar with the unscored sheet to the left.

According to the instructions, to cut on the right side of the bar, you would need a left handed cutter. Maybe you use the thing differently than I think.

Confused? I am.

Ron

Ron Coleman wrote:

Lisa Allen wrote:Nadine, I got a large custom made Scoreboard from the folks that make them and it is great. It accomodates a whole sheet of BE which can be stripped in about 10 minutes using your own cutter. It is just a base board with a set bar at the bottom and a raised perpendicular bar that the glass slides under. Make a mark on the bottom bar and start sliding and scoring, using the perpendicular bar as a guide for your cutter.

Lisa

The instructions on the Scoreboard look backwards to me. If I'm right handed , I would have the cutter in my right hand and would want to cut on the right side of the vertical bar with the unscored sheet to the left.

According to the instructions, to cut on the right side of the bar, you would need a left handed cutter. Maybe you use the thing differently than I think.

Confused? I am.

Ron

Hey Ron-

I got a modified version that doesn't have the angled rod, just the bottom aluminum bar and the raised perpendicular one, so with this one you can use it as a righty or a lefty. Just depends on which way you want to slide the glass. You can use either side of the perpendicular bar to butt your cutter up against. No instructions with this one, its made just for up and down cuts which is all I wanted.

Lisa

Lisa Allen wrote:

Ron Coleman wrote:

Lisa Allen wrote:Nadine, I got a large custom made Scoreboard from the folks that make them and it is great. It accomodates a whole sheet of BE which can be stripped in about 10 minutes using your own cutter. It is just a base board with a set bar at the bottom and a raised perpendicular bar that the glass slides under. Make a mark on the bottom bar and start sliding and scoring, using the perpendicular bar as a guide for your cutter.

Lisa

The instructions on the Scoreboard look backwards to me. If I'm right handed , I would have the cutter in my right hand and would want to cut on the right side of the vertical bar with the unscored sheet to the left.

According to the instructions, to cut on the right side of the bar, you would need a left handed cutter. Maybe you use the thing differently than I think.

Confused? I am.

Ron

Hey Ron-

I got a modified version that doesn't have the angled rod, just the bottom aluminum bar and the raised perpendicular one, so with this one you can use it as a righty or a lefty. Just depends on which way you want to slide the glass. You can use either side of the perpendicular bar to butt your cutter up against. No instructions with this one, its made just for up and down cuts which is all I wanted.

Lisa

OK that answers the question. Looks like a good system for the strips.

Ron

Ron, We have a scoreboard and we are both right handed. We score on the right side of the bar that is perp. or angled. Maybe we are using it wrong but Mark used it this way when I saw him use it. Maybe the instructions or the picture were printed wrong.